Shop Bedding at Solseal - Next Day Delivery on all Stock Items

UltraTile ProPave Mortar – 20kg

Neil Aldam — Wed, 22 May 2024 12:57:13 +0000

Next working day delivery if ordered by 2pm

UltraTile ProPave Mortar – 20kg

UltraTile ProPave Mortar is a fibre modified cement binder which, when mixed with graded aggregates and water, can produce a rapid drying high strength bedding mortar ready to receive floor finishes such as porcelain/natural stone tiles etc. UltraTile ProPave Mortar can be used to form falls within patios and driveways.

For use with type 1 hardcore
Fast track installation
Fibre reinforced for added strength and durability
Simply mix with sharp sand and water
Dual-mix ratio for heavy or light trafficked areas
Maintains porosity to facilitate drainage
Approved for use with Porcelain and Natural Stone
Depth: 30-100mm
Internal and external use
Part of the ProPave External Tiling System
Size: 20kg Product calculator based on ratio of 6:1 aggregate

More product detail

The post UltraTile ProPave Mortar – 20kg appeared first on Solseal.

Mapei MapePave Bedding Mortar – 25kg

Neil Aldam — Thu, 21 Mar 2024 14:41:25 +0000

Next working day delivery if ordered by 2pm

Mapei MapePave Bedding Mortar

MapePave Mortar is ideal for bedding 20mm porcelain, it is rapid curing (just 12 hours for foot traffic) thin application, with low shrinkage and is compliant with BS 7533. Pre-blended, just mix with water, to be used in conjunction with MapePave Slurry.

Paving mortar ideal for bedding 20mm porcelain
BS 7533 compliant
Rapid curing – open to pedestrian traffic 12 hours
Just mix with water
Thin application
Low shrinkage
Used in conjunction with MapePave Slurry

More product detail

The post Mapei MapePave Bedding Mortar – 25kg appeared first on Solseal.

UltraScape Perma Bed

Neil Aldam — Fri, 06 Aug 2021 08:36:13 +0000

Free next working day delivery if ordered by 2pm

UltraScape Perma Bed Permeable Bedding Mortar

The material is specifically designed to drain away any water migrating into the pavement via cracks or damaged areas. Water that is not removed can cause failure of the pavement ultimately via hydraulic action from repeated trafficking.

Can be laid from 10-100mm in one pass
Shrinkage compensated
BS 7533 compliant –allows the free passage of water through it
Reduces water penetration related pavement failures
Reduces the likelihood of reflective staining
Freeze/thaw resistant
Small contractor friendly units
Pre-blended – just add water
Open to pedestrian traffic in 12 hours
Open to vehicular traffic in 24 hours

Applications

UltraScape Perma Bed is specifically formulated to meet and exceed the strict demands of BS 7533. The product provides a perfect bound base for natural stone paving and cobbles, concrete paving, flags and block paving, which once laid with UltraScape Perma Bed are able to accept foot traffic after just 12 hours and vehicular traffic after 24 hours. The material is specifically designed to drain away any water migrating into the pavement via cracks or damaged areas. Water that is not removed can cause failure of the pavement ultimately via hydraulic action from repeated trafficking.

Technical

UltraScape Perma Bed is formulated from selected cements and graded fillers. UltraScape Perma Bed is supplied pre-blended in 25kg bags. The product can be laid from 10mm to 100mm in one pass with greater depths achievable using successive layers. The material mixes easily on- site with the addition of water and provides a compressive strength of >35N/mm2 after 28 days complying fully with BS 7533.

UltraScape Perma Bed is fully permeable and is frost resistant. The free passage of water through the cured matrix of the product ensures that correctly laid paving should not suffer from reflective staining emanating from the underside of the paving elements.

This material along with most standard setting cementitious products should not be used in temperatures below 5°C*.
(* Ultrascape bedding mortars can be used below 5°C, only if the following conditions are met.

a) The ground to be laid upon is not frozen.
b) The temperature is 2°C and rising.
c) The product must be protected from frost.)

Preparation

It is of vital importance that the supporting layer that is to receive UltraScape Perma Bed is stable and not liable to settlement or heave. Supporting structures must be cleaned, pre-soaked and all ponded water must be removed prior to application. To promote bond, the supporting layer can be primed using UltraScape pro-prime slurry primer. Please note that this product is suitable only for bound/rigid construction, not for unbound/flexible applications.

Mixing

Add 1.75 litres of clean water to a suitable mixing vessel. Slowly add the contents of one 25kg bag. Mix mechanically for a minimum of 3 minutes and a maximum of 5 minutes. Do not add extra water or part mix bags.

For more information on UltraScape Perma Bed click here

To view our extensive range of landscaping products click here

The post UltraScape Perma Bed appeared first on Solseal.

UltraScape SlipBond

Neil Aldam — Fri, 06 Aug 2021 08:26:34 +0000

Free next working day delivery if ordered by 2pm

UltraScape SlipBond Vertical Stone and Brick Slip Adhesive

UltraScape SlipBond is a flexible cladding adhesive for internal and external use. It consists of blended cements, graded fillers and additives and a high level of redispersible powder polymer. It is specially formulated with extended workability for fixing brick slips and natural stone to a range of substrates including sand/cement render, brick and block work and can be used for wall and floor applications as well as with external and internal wall installation systems.

Ideal for use in all weathers
Applied to a thickness of 3mm – 20mm
Frost resistant
Suitable for: brick slips and natural stone
Can be used with external wall installation systems
Extended workability
Suitable for underfloor heating
External / internal use
20kg paper bag

Applications

UltraScape SlipBond is a flexible cladding adhesive for external and internal floor and wall applications. It consists of cements, graded fillers and additives and a high level of redispersible powder polymer. It is specially formulated with extended workability for fixing brick slips and natural stone to a range of substrates including sand/cement render, brick and block work and can be used with external wall installation systems.

Technical

UltraScape SlipBond is a fully pre-mixed dry-pack which only requires the addition of water on-site. It can be applied to a thickness of 3mm- 20mm up to 1m2 at a time.

Preparation

The preparation of the surface to be treated is of the greatest importance. Care must be taken to remove all loose material, debris, laitance, grease, paint and efflorescence. The concrete /masonry/ substrate should be thoroughly dampened with water. Any surplus water should be removed prior to commencing application.

Mixing

UltraScape SlipBond should be added slowly to 5.2 litres of clean water per 20kg bag and mixed thoroughly, ideally with a forced action mixer for 3 minutes to give a slump free easily worked adhesive. Once mixed the mortar is immediately ready for use and has a pot life of approximately 2 hours at 20°C. Mix only sufficient material to be used within the pot life, do not remix or re-wet.

Application

Use a trowel to apply a layer of mortar on to the substrate with sufficient force to ensure a good bond. On large format stone it is advisable to back butter the stone unit prior to embedment. Once application of the mortar bed has taken place please ensure that the stone is applied within 25 minutes.

Cleaning
Tools should be cleaned in water immediately after use to remove excess materials.

Quality Assurance
All products are manufactured in a plant whose quality management system is certified / registered as being in conformity with BS EN ISO 9001, ISO 14001 and OHSAS 18001. Our products are guaranteed against defective materials and manufacture and will be replaced or money refunded if the goods do not comply with our promotional literature.

We cannot however accept responsibility arising from the application or use of our products because we have no direct or continuous control over where and how projects are used. All products are sold subject to our conditions of sales, copies of which may be obtained upon request.

To view our extensive range of landscaping products click here

The post UltraScape SlipBond appeared first on Solseal.

UltraScape Eco Bed

Neil Aldam — Fri, 06 Aug 2021 08:01:33 +0000

Free next working day delivery if ordered by 2pm

UltraScape Eco Bed

UltraScape Eco Bed is an environmentally friendly fine bedding mortar manufactured to meet and exceed the strict requirements of BS 7533. It contains 20% recycled materials, significantly reducing the consumption of virgin aggregates. It is ideal for schemes looking to achieve an ‘excellent’ CEEQUAL award, or where a BREEAM assessment is to be conducted on your building.

Can be laid from 10mm – 100mm
Shrinkage compensated
BS 7533 compliant
Small contractor friendly units
Pre-blended – just add water
Open to pedestrian traffic in 12 hours
Open to vehicular traffic in 24 hours
Long-term durability
Size: 25kg

Applications

UltraScape eco-bed is specifically formulated to meet and exceed the strict demands of BS 7533. The product provides a perfect bound base for natural stone paving and cobbles, concrete paving, flags, block paving and 20mm Porcelain tiles, which, once laid with UltraScape Eco Bed are able to accept foot traffic after just 12 hours and vehicular traffic after 24 hours. The material is also not subject to environmental erosion, which can lead to increased point loads on slabs and consequent breakage.

Technical

UltraScape Eco Bed is formulated from selected cements and graded fillers. The pre-blended fine bedding concrete is supplied in 25kg bags or alternatively, for those large projects, in 30 tonne bulk silos. The product can be laid from 10mm to 100mm in one pass with greater depths achievable using successive layers. The material mixes easily on-site with the addition of water and provides a compressive strength of 45N/mm2 after 28 days complying fully with BS 7533. This material should not be used in temperatures below 5oC.

Preparation

It is of vital importance that the supporting layer that is to receive UltraScape Eco Bed is stable and not liable to settlement or heave. Supporting structures must be cleaned, pre-soaked and all ponded water must be removed prior to application. To promote bond, the supporting layer can be primed using UltraScape pro-prime slurry primer. Please note that this product is suitable only for bound/rigid construction, not for unbound/flexible applications.

Mixing

Add between 2.4 and 2.8 litres of clean water to a suitable mixing vessel. Slowly add the contents of one 25kg bag. Mix mechanically for a minimum of 3 minutes and a maximum of 5 minutes. Do not add extra water or part mix bags.

Priming

To increase overal product performance, prime the supporting layer with Ultrascape pro-prime before applying UltraScape eco-bed. Priming the roadbase is not a requirement of the British Standard for pavements constructed on a bound base. It is of vital importance that the underside of all paving elements are primed in accordance with BS 7533. For full details consult the manufacturer or refer to the UltraScape pro-prime datasheet.

To view our extensive range of landscaping products click here

For more information on UltraScape Eco Bed click here

The post UltraScape Eco Bed appeared first on Solseal.